Engineering for Degree/Professional Level Engineers

From 51 C$ /h

A master’s graduate with First Class Honours in Advanced Mechanical Engineering from University of Leicester. Since, I completed my course in September 2019. I have worked as a Teaching Assistant in the department of engineering. I was trained and certified to teach in higher education from Leicester Learning Institute. I have assisted in demonstrating mechanical oriented first year labs concerning flow measurements in pipes, and electrical oriented labs based on circuit design and analysis using PSpice. Also, assisted in second year labs helping students to learn about material selection in electromechanical devices using CES Edupack software, as well as different engineering materials micro structural properties and processing. Furthermore, I have helped in for fourth year module involving conceptual design process for turbofan engines with improvements in aero engine design configurations. Overall, my aspects of teaching involved concepts related to designing, modelling, real life applications, mathematical calculations, physical and chemical sciences.

As a tutor, I would like to give my best abilities to improvise any individuals knowledge and make sure that they succeed in each & every aspects. At the same time, my commitment to teach with supporting and delivering the learning materials with at most reliability will always be my utmost priority. I will give what it takes to make an individual completely transformed into a knowledgeable individual. I believe one becomes intelligent by not just learning the concepts, but making the best use of it by applying in the real world.

Extra information

Online

Location

Online from United Kingdom

About Me

A master’s graduate with First Class Honours in Advanced Mechanical Engineering from University of Leicester. Since, I completed my course in September 2019. I have worked as a Teaching Assistant in the department of engineering. I was trained and certified to teach in higher education from Leicester Learning Institute. I have assisted in demonstrating mechanical oriented first year labs concerning flow measurements in pipes, and electrical oriented labs based on circuit design and analysis using PSpice. Also, assisted in second year labs helping students to learn about material selection in electro mechanical devices using CES Edu pack software, as well as different engineering materials micro structural properties and processing.

Furthermore, I have helped in for fourth year module involving conceptual design process for turbofan engines with improvements in aero engine design configurations. Overall, my aspects of teaching involved concepts related to designing, modelling, real life applications, mathematical calculations, physical and chemical sciences.

As a tutor, I would like to give my best abilities to improvise any individuals knowledge and make sure that they succeed in each & every aspects. At the same time, my commitment to teach with supporting and delivering the learning materials with at most reliability will always be my utmost priority. I will give what it takes to make an individual completely transformed into a knowledgeable individual. I believe one becomes intelligent by not just learning the concepts, but making the best use of it by applying in the real world.

Education

September 2018-2019: University of Leicester, United Kingdom- M.Sc. in Advanced Mechanical Engineering. Score- Distinction (70%)
• Relevant Modules- Matlab & CAD Modelling (Solid Works), Understanding Surfaces in Engineering, Aerospace Materials, Dynamics of Mechanical Systems, Computational Fluid Dynamics.

• M.Sc. project work carried out on Co-deposition of nickel-SiC using PRP techniques to produce nanocomposites.

August 2013-July 2017: Rajarajeswari College of Engineering, Bengaluru, India- Bachelor of Engineering in
Mechanical Engineering. Score- First Class (68.5%).

• Relevant Modules- Automation Lab, Material Science and Metallurgy, Manufacturing Process, Basic Thermodynamics, Mechanics of Composite Materials, Mechanics of Materials, Mechanical Vibrations, Mechatronics, Hydraulics and Pneumatics, Tool Design.

July 2011-March 2013: Pre-University Education, Bengaluru, India. (A-levels Equivalent) Score- First Class (79.2%)
• Relevant Modules- Physics, Chemistry, Mathematics, Electronics.

March 2011: Central Board of Secondary Education, Bengaluru, India. (GCSE Equivalent) Score- (79.8%)

Experience / Qualifications

1 October 2019-April 2020: Teaching Assistant, University of Leicester, United Kingdom.
• Achieved training to teach in higher education at Leicester Learning Institute.
• Involved in concepts related to flow measurements in pipes and electrical oriented lab based on circuit design and analysis using PSpice.
• Involved in analysis for material selection in electromechanical devices using CES Edupack software.
• Demonstrated different engineering materials microstructural properties and processing.
• Engaged in providing a conceptual design process for a turbofan engine with improvements in aero engine design configurations.

Age

Teenagers (13-17 years old)

Adults (18-64 years old)

Seniors (65+ years old)

Student level

Beginner

Intermediate

Advanced

Duration

30 minutes

45 minutes

60 minutes

90 minutes

120 minutes

The class is taught in

English

Skills

Mechanical engineering

Industrial engineering

Electrical engineering

Reviews

Availability of a typical week

(GMT -04:00)

New York

Online via webcam

Mon

Tue

Wed

Thu

Fri

Sat

Sun

00-04

04-08

08-12

12-16

16-20

20-24

Reza

4.64

(25)

I hold a PhD in Mechanical Engineering and currently work as a post-doctoral researcher in the Aerospace Engineering Faculty at TU Delft (Delft University of Technology).

My extensive teaching experience covers a wide range of engineering courses, including:

- Mathematics: algebra, linear algebra, probability, calculus, differential equations, intellectual math, and advanced engineering mathematics.

- Mechanical Engineering: Statics, Dynamics, Mechanics of materials, Mechanical design, control, vibration, Fluid Mechanics, Thermodynamics, Heat transfer, Engineering drawing, Applied Mechanics, Composite Structures, Flight, Machine Elements, Manufacturing, 3D printing, and more.

- Physics: mechanics, momentum and energy, electricity, charge and current, electric and magnetic fields, waves, particle physics, nuclear decay, astrophysics, cosmology, oscillations, etc.

- CAD/CAM Software: Autocad, Solidworks.

- Mechanical Design Packages: ANSYS, APDL programming, ABAQUS, MATLAB, Symbolic MATLAB, LS-DYNA.

My research and teaching interests are diverse, including:
• Additive manufacturing
• Mechanical metamaterials
• Acoustical metamaterials
• Electromagnetic metamaterials
• Aeroacoustics
• Soft matter and soft robotics
• Fatigue and fracture mechanics
• Experimental mechanics
• Multiscale numerical modelling
• Biomaterials
• Porous materials
• Manufacturing of medical devices and implants
• Deep learning
• Image processing
• Topology optimization
• Origami and Kirigami structures
• Self-folding and self-assembly structures
• Tissue engineering
• Permeability in porous materials
• Fluid-Solid Interaction

I understand that not all teachers excel in teaching Engineering and Mathematics courses and explaining their importance to students. Courses with strong mathematical backgrounds may become boring for students who lack a solid mathematical basis. To address this, I take a student-centered approach, starting from the basics to actively engage all students, including those with weaker mathematical backgrounds. I also provide practical examples to demonstrate the real-world significance of what they are learning, inspiring and fostering their interest in the subject matter.

If you have any additional questions before starting a class, please feel free to ask me. I am here to assist! :)

Matías

4.64

(25)

Do you dream of mastering the art of electronic design, advanced programming and creating awesome robots? Do not look any further ! I offer personalized courses that will guide you into the exciting world of engineering, with an emphasis on electronics, programming and robotics.

Electronics: Learn to create circuits, understand components, and carry out innovative electronics projects.

Programming: Immerse yourself in the world of coding and develop programming skills, from classic languages to new technologies.

Robotics: Explore the basics of robotics, create autonomous robots, and discover how to bring your ideas to life.

Miscellaneous Projects: Use popular platforms like Arduino, Raspberry Pi, and more to bring your unique and exciting projects to life.

Whether you're a beginner or looking to deepen your skills, my classes are suitable for all levels. With interactive lessons, challenging projects, and expert guidance, you'll progress quickly and confidently.

Don't let your dreams of innovation wait any longer. Join me on this rewarding learning adventure and start creating today!

Alonso

4.64

(25)

I am a Full Professor of Mechanical Engineering with 30 years of experience in areas such as Strength of Materials, Stability, Physics (Kinematics and Dynamics), Statics, Elasticity, Solid Mechanics, Machine Elements, Stress Analysis, Structures and Advanced Materials Mechanics . I emphasize teaching through problem solving and practical applications.
The Strength of Materials classes include topics such as: Stress analysis. Axial load, bending, Torsion, Transverse load, Combined stresses, Stress transformation, Energy methods, Calculation of deflections in beams, statically indeterminate problems, buckling, shear center, compound bending and asymmetric bending, Castigliano's theorem, Mohr's method , Virtual work, Creep and Fracture Criteria, etc.

Youssef

4.64

(25)

Hello, I am a doctor in electrical engineering and associate professor in engineering sciences, experienced in the field of electrical engineering, I offer support courses in the subjects of engineering sciences (electronics, automation, electrical engineering, automation, programming).

Digital electronics
Analog electronic
electromagnetism (propagation of high frequency waves)
Automatic (continuous, sampled)
electrical engineering (transformers, electrical machines, switching power supply)
C / c ++ programming, Assembler, ARM, STM32
renewable energy (wind, PV)
engineering Sciences
RDM
Python,VHDL
PIC Microprocessor and Microcontroller
Signal processing and data acquisition
Engineering Sciences

These courses allow the student to get up to speed and regain confidence in all scientific subjects, just as they prepare him effectively for the Baccalaureate, the Preparatory Classes or various examinations of the engineering classes.

COURSE OBJECTIVES AND PEDAGOGICAL APPROACH

Resumption and deepening of fundamental concepts through exercises with course reminders.

Put the student in a situation of questioning and research.

Respond to individual issues and questions

Exercise training in order to achieve real mastery of the content.

Learn to build theoretical reasoning from observable facts or hypotheses.

Specific preparation for higher education requirements (in-depth content, increase in work capacity, enrichment of scientific background)

This educational approach is effective since it has often led me to interesting results with my students.

Associate professor provides support courses in electrical engineering

Adam

4.64

(25)

===================Satisfied or refunded=======================
Hello, I am a doctoral student in electrical engineering and associate professor in engineering sciences, experienced in the field of electrical engineering, I offer courses in engineering sciences (Electronics, automatics, electrical engineering, automation, programming).
Computational Sciences and Technology SNT
IS engineering sciences
Numerical and computer science SNI
Digital electronics
Analog electronic
electromagnetism
Signal processing and data acquisition
Automatic (discrete, continuous)
electrical engineering (transformers, electrical machines, switching power supply)
C/C++ Programming, Assembler, ARM, STM32
renewable energy (wind, PV-solar)
RDM - strength of materials mechanics of solids
Python and SYSML
PIC microcontroller
Microprocessor
MATLAB, proteus
Preparation for competitions
Supervision of graduation projects
CAPLP Electrotechnical and Electronic Electrical Engineering
CAPLP and BTS subjects and answers
Correction caplp 2017 CAPLP 2018 CAPLP 2019 CAPLP 2020
CORRECTION OF BTS TESTS

Yassine

4.64

(25)

Are you looking to improve your skills in mathematics, physics or technical skills? I offer courses adapted to your level, whether you are in middle school, high school or even in higher education.

We will cover key concepts in a clear and structured manner to help you master the fundamentals, solve complex exercises and prepare for exams. Whether for support courses or to deepen your knowledge, I am here to guide you.

Ali

4.64

(25)

I teach Electrical and Electronic Engineering online to university students, postgraduates, college students and serious self learners across the UK and Europe. Lessons are in English.

I hold an MSc in Electronics and Electrical Engineering with Distinction and I teach as a Visiting Lecturer on a Master's level module at a UK university. I also work as a freelance electronics engineer, designing circuit boards and writing firmware for real clients, and I have two accepted international conference papers. I set and mark university assignments myself, so I know where marks are won and lost on lab reports, coursework and project write ups.

Who this is for

Undergraduates on electrical, electronic, mechatronic or general engineering degrees at any European university. Final year, Master's and thesis students working on an engineering project. A Level, IB and college students taking physics or engineering. Career changers and self taught learners who want the fundamentals done properly rather than picked up from scattered videos.

I work with students on UK, IB and continental European programmes. An unfamiliar syllabus or a module structured differently from the UK is not a problem. Send me the material and I will work from it.

What we cover

Circuit analysis in DC and AC, including Kirchhoff's laws, Thevenin and Norton equivalents, superposition, phasors and AC power. Operational amplifiers and analogue electronics. Digital electronics and logic design. Signals and Systems and Digital Signal Processing, covering Fourier analysis, Laplace and z transforms, sampling and filter design. Control systems, transfer functions, root locus, Bode plots, stability and PID tuning. Semiconductor devices and power electronics. Embedded systems and microcontroller programming in C with Arduino, ESP32 and PIC. Simulation and tooling including MATLAB, Simulink, LTspice, Multisim and Proteus. Circuit board design in KiCAD. Lab reports, coursework, project supervision and exam technique.

How lessons work

Send me your lecture notes, assignment brief, lab sheet or the circuit that refuses to work, and I plan the session around it before we meet. Nothing generic.

Most students are stuck on one or two specific ideas rather than a whole module, so the first job is finding out which. Then we work through it with proper worked examples and real circuit diagrams, and I hand the problem back to you while I watch and correct, because you learn far more doing it than watching me do it.

If the real gap is the maths underneath a topic, complex numbers, phasors, Laplace transforms, we go back and fix that first, because everything after it depends on it.

You finish each session with annotated notes and a clear next step, and you can message me between lessons with questions.

Practical details

Lessons are online over Google Meet or Zoom, with screen sharing and a shared whiteboard so we can draw circuits and work through derivations together. Sessions run 60 or 90 minutes. Evenings and weekends available across European time zones.

Tell me your module, your deadline and exactly where you are stuck, and I will come back with a plan for the first session.

Dhanush

4.64

(25)

Electrical engineering is a current trend and upcoming future necessity for people day to day life. so I will teach about how our electrical engineering help our day to day life and it remain use full and safe to our environment and people . People of this world must know about safety measures of electrical system. Also I will teach how to protect our environment and nature by using electrical engineering concept. The above content what I mentioned is learned by future students and taught by me.

Yassine

4.64

(25)

As a tenured professor of Engineering Sciences, I help students succeed in exams and competitive entrance exams. I teach in preparatory classes (MPSI, MP, PSI, etc.) and up to the undergraduate level. My method: understand the material, practice rigorously, structure your reasoning, and tackle well-chosen exercises and problems. Each session includes targeted exercises, methodological advice, and personalized follow-up. You will receive a video recording and an annotated PDF after each lesson. Lessons are held online via Google Meet, 7 days a week, with flexible scheduling. I am available between sessions to answer questions. Contact me for an initial discussion.

Derek

4.64

(25)

Patient, practical tuition in Maths, Physics and Engineering Science from a mechanical engineer and further-education lecturer. I support Scottish National, Higher and Advanced Higher courses, GCSE learners throughout England, college and university students, apprentices and adult learners. Lessons are tailored to your level and goals, with calculations explained step by step, regular checks for understanding, revision planning, exam technique and real-world engineering examples. Topics can include algebra, trigonometry, calculus, statistics, mechanics, thermodynamics, fluid mechanics, electrical circuits and applied engineering calculations. I hold a Bachelor’s Degree in Mechanical Engineering, have over 25 years of engineering experience, five years of teaching experience, and a current PVG disclosure. Tuition is available online and in person in Glasgow, Monday to Saturday.

Mayank

4.64

(25)

In this 30-minute class, we will understand the two core components of a microprocessor: the ALU (Arithmetic Logic Unit) and the Control Unit. I will explain their structure, functions, and how they work together to execute instructions, using simple diagrams and practical examples. The goal is to build a clear understanding of how a microprocessor processes and controls data.

Aashish

4.64

(25)

Master Engineering Drawing, Technical Drawing and Engineering Graphics with a practical, step-by-step approach.

Are you a student who finds engineering drawing difficult to visualize? Do you want to understand orthographic projections, front/top/side views, sections, dimensions, scales, and 3D shapes instead of simply memorizing drawing procedures?

I provide friendly, patient and practical online coaching in Technical Drawing, Engineering Drawing, Engineering Graphics, CAD and Engineering Design for students from high school through university, as well as professionals who want to strengthen their technical drawing and design skills.

What You Will Learn

The classes are designed to develop both your drawing skills and your ability to visualize engineering objects in 2D and 3D.

Topics can include:

Engineering Drawing fundamentals and drawing conventions
Visualization of 2D and 3D geometric shapes
Orthographic projection
Front, Top, Side and Back views
First-angle and Third-angle projection
Isometric views and pictorial representation
Sectional views and sectional drawings
Hidden lines, centre lines and construction lines
Dimensions, annotations and engineering symbols
Scales and measurement
Geometrical constructions
Development of surfaces
Intersections of solids
Tolerances and basic fits
Engineering drawing standards and conventions
Reading and interpreting engineering drawings
Production-oriented technical documentation
Mechanical components and product drawings
Basic engineering design principles
From Hand Drawing to CAD and 3D Models

I also help students understand how traditional engineering drawing connects with modern Computer-Aided Design (CAD).

You can learn how a product or mechanical component can be:

Visualized → Sketched → Dimensioned → Created in CAD → Converted into a 3D Model → Prepared for Manufacturing / 3D Printing

Depending on your requirements, lessons can include AutoCAD, 2D drafting, 3D modelling and engineering design workflows.

The objective is not only to teach you which commands to use, but to help you understand why a drawing is created in a particular way and how engineers use drawings to communicate a design.

Practical, Student-Focused Teaching

My teaching approach is based on understanding through visualization and practice.

Instead of simply demonstrating a drawing, I explain:

How to visualize the object before drawing it
How to identify the different surfaces and views
How the front, top and side views are related
How to determine the required dimensions
How to construct the drawing step by step
How to avoid common drawing mistakes
How to interpret engineering drawings correctly
How the same concept is applied in CAD and real-world design

Lessons include worked examples, practical exercises and real engineering/product examples so that students can gradually develop confidence and independence.

Who Are These Classes For?

These lessons are suitable for:

High school students studying technical/engineering drawing
Diploma students
Mechanical Engineering students
Civil Engineering students
Architecture students
Industrial Engineering students
Product Design students
Manufacturing Engineering students
Other engineering students studying Engineering Graphics or Engineering Drawing
Students preparing for examinations
Beginners learning CAD and technical drawing
University students working on drawing or CAD projects
Professionals who want to refresh or improve their technical drawing skills

Beginners are welcome. No advanced prior knowledge is required.

Online & Interactive Lessons

All lessons are conducted online and interactively.

Depending on the topic, I can use:

Screen sharing
Live drawing demonstrations
CAD demonstrations
2D drafting
3D modelling
Step-by-step problem solving
Practical drawing exercises
Real-world engineering examples

You can bring your specific syllabus, textbook exercises, assignments, CAD projects or exam topics, and the lessons can be adapted to your requirements.

Learn to Think Like a Designer

Engineering drawing is more than producing a neat drawing on paper. It is a method of visualizing ideas, communicating designs and understanding how objects are constructed and manufactured.

My goal is to help you move from:

“I don't understand this shape.”

to

“I can visualize it, draw its views, add the required dimensions and understand how it would be represented in CAD and manufactured.”

Whether you are starting from zero, preparing for an examination, struggling with engineering graphics, learning CAD, or working on a design project, I will guide you step by step at your own pace.

Book a lesson and let's make Engineering Drawing and CAD easier, more visual and more practical.

Hend

4.64

(25)

In this lesson we cover the basics of statics, the science that studies stationary objects under the influence of different forces, and is the cornerstone of engineering subjects such as mechanics and construction.
What you will learn in this lesson:
• The concept of power, its types, and methods of representing it
• Analyzing forces into their components
Conditions for equilibrium of bodies
• Solve practical examples step by step
The lesson is suitable for engineering students of all specializations, and for anyone who wishes to build a strong understanding of the material before moving on to advanced subjects.

Mohamed

4.64

(25)

Teaching electrical engineering online to university students

I offer online private lessons for engineering college students, focusing on simplifying engineering concepts, solving problems step by step, and practicing exam and project questions.

I help students understand the material from the ground up instead of relying on memorization, using practical examples, illustrations and simulations when needed.

The subjects I teach include:

Electrical Circuits
Electrical Machines
- Electrical Power Systems
Power System Protection
Electrical Installation & Distribution
Energy Conversion
Renewable Energy Systems
High Voltage and High Voltage Engineering
- Transformer stations and substations
- Electronics and basic electronic circuits
- Basic Control Systems
Engineering mathematics used in electrical engineering

During the lecture, I focus on:

1. Explain the concept in a simple and organized way.
2. Derivation of important laws and equations.
3. Solve various examples and problems step by step.
4. Training the student on exam questions.
5. Explaining common mistakes and how to avoid them.
6. Use MATLAB/Simulink, ETAP and simulation when needed.
7. A comprehensive review before tests and exams.

Teaching method:

- Individual lectures or small online groups.
- Live and interactive explanation via Zoom or Google Meet.
- Sharing the screen and writing on the electronic whiteboard.
- The possibility of recording the lecture as agreed.
- Providing summaries and practice problems for review.

The goal: for the student to be able to understand the material, solve problems on their own, and prepare confidently for exams and engineering projects.

Hakan

4.64

(25)

I offer personalized Mechanical Engineering lessons for university students who want to strengthen their understanding of core engineering subjects, prepare for exams, solve assignments, or improve their problem-solving skills.

My main teaching areas include:

Thermodynamics

Fluid Mechanics

Heat Transfer

Engineering Mathematics

Calculus

Physics

Computational Fluid Dynamics (CFD)

ANSYS Fluent fundamentals and engineering applications

My lessons focus on understanding the physical and mathematical principles behind engineering problems rather than simply memorizing formulas. I explain concepts step by step, work through practical examples, and adapt the lesson to the student's current level and objectives.

Lessons can be used for exam preparation, topic revision, homework and problem-solving practice, or structured study throughout the semester.

As a mechanical engineer with university teaching and laboratory experience, I aim to connect theoretical concepts with real engineering applications whenever possible.